HP ProLiant ML110 G5 Server with Windows Server 2008 Intel Xeon Processor 3065 ( 2.33Ghz, 65W, 1333FSB. 4MB ), 2GB PC2-6400 ECC (DDR2-800Mhz), NC105i PCIe Gigabit server Adapter, SATA Controller with embedded RAID, Two (2) 160GB SATA Hard Disk Drive.
11-08-201701:42 AM
Hi,
i have been trying for a long time for getting drivers for my server HP ProLiant ML110 G6 expecialy ethernet controller.someone plss help me to find it out as soon as possible.
Regards
Fayiz
11-08-201707:00 AM
Hi:
You need the driver for the broadcom gigabit ethernet controller shown in your screenshot.
Here is a partial copy and paste of the driver setup information file which shows support for that hardware ID...
[Version]
Signature = '$Windows NT$'
Class = Net
ClassGUID = {4d36e972-e325-11ce-bfc1-08002be10318}
CatalogFile = b57nd60x.cat
Compatible = 1
Provider = %HPQ%
DriverVer = 09/12/2014,16.8.0.4
[Manufacturer]
%HPQ% = HPQ, NTx86.6.0, NTx86.6.1
[HPQ.NTx86.6.0]
%NC1020% = NC1020_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1654&SUBSYS_3100103c
%NC330i% = NC330i_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1655&SUBSYS_18d2103c
%NC331FLR% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1657&SUBSYS_169d103c
%NC331i% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1657&SUBSYS_22be103c
%NC331T% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1657&SUBSYS_3383103c
%NC331i% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1657&SUBSYS_3372103c
%NC330iSPI% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1657&SUBSYS_1904103c
%NC331FLR% = NC329a_LHinst_A0.NTx86.6.0, PCIVEN_14e4&DEV_1657&SUBSYS_169d103c&REV_00
%NC331T% = NC329a_LHinst_A0.NTx86.6.0, PCIVEN_14e4&DEV_1657&SUBSYS_3383103c&REV_00
%NC331i% = NC329a_LHinst_A0.NTx86.6.0, PCIVEN_14e4&DEV_1657&SUBSYS_3372103c&REV_00
%NC332T% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_165F&SUBSYS_1786103c
%NC332i% = NC329aS_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_165F&SUBSYS_193d103c
%NC332i% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_165F&SUBSYS_2133103c
%NC332i% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_165F&SUBSYS_22e8103c
%NC332i% = NC329a_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_165F&SUBSYS_22eb103c
%NC105T% = NC105T_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_165a&SUBSYS_7052103c
%NC105i% = NC105i_LHInst.NTx86.6.0, PCIVEN_14e4&DEV_165a&SUBSYS_7051103c
%NC107i% = NC107i_LHInst.NTx86.6.0, PCIVEN_14e4&DEV_165b&SUBSYS_705d103c
%NC150T% = NC150T_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1654&SUBSYS_3226103c
%NC320i% = NC320i_LHinst.NTx86.6.0, PCIVEN_14e4&DEV_1659&SUBSYS_7032103c
You may also want to post any questions you have regarding your server on the HPE community support forum--ML servers section...
- Open Menu
Didn't find what you were looking for? Ask the community
HP Proliant ML110 G5 embedded raid setup
Hi all,
I have the above server, with 4x149GB SATA HDDs. Forgive me if I use terms incorrectly, the server was set up with 2 arrays of RAID1 (not by me), and recently I tried to remove them and set up a RAID10. I don't know what I'm doing wrong but when I run windows setup I only see 149GB of space instead of ~300GB.
Here's what I did:- 1)Press F8 to enter the RAID config menu 2) Deleted all the existing raid config 3) Created a new array by highlighting all the 4 hdds (Ins key), selected RAID10, label, stripe size (64kb), Quick Init. 4) Marked RAID as bootable. 5) Exit utility
At reboot, I can see it shown as RAID10 297GB at startup which seems correct. But when I start to run Win Server 2012 R2 setup, I see 4 drives at 149GB each, but 3 of them cannot be installed on. Only the first drive is allowed. On the other 3 it says something like 'windows cannot be installed on this drive'. Then I tried with a Win8 OS, and VMWare ESXi 6.0 setup, same thing.
I tried RAID0 with 2 drives, which should show 300GB as well but didn't.
I must have set up the RAID incorrectly. Any suggestions?